Guru Corporation

Description

G-FINE ULTRAFINE is a new generation Supplementary Cementitious material (SCM) with a built-in high tech content. It is processed based on high glass content with high reactivity obtained through the process of controlled granulation process results in unique particle size distribution. The raw materials are composed primarily of low calcium silicate based mineral additives.

 Its latent hydraulic property and pozzolanic reactivity results in an enhanced hydration process. Addition of G-FINE improves the packing density of the paste component. In spite of its high fineness the results are in lowering water demand, admixture dosage and hence improving strength and durability parameters of concrete at all ages.

G-FINETM are observed in the concrete mix design, the initial rate of strength development was found to be increased or similar as other pozzolanic materials.

Application

§   Roads, Residential, Commercial structures

§   Producing mass concrete for raft and pile foundations

§   Low water to binder rations for high performance concrete

§   Better retention of workability and faster initial strength gain

High Strength construction work in low or high temperature weather

Benefits

 

          · Increase compressive strength ,permeability, workability of concrete

· Improves the durability of concrete  

· It can be used in waterproofing as an additive

· It can decrease the heat of hydration

·Resistance against saltwater & chemicals

· Non-Toxic, Eco friendly

            · Cost effective, economical solutionDOSAGE These goals are accomplished using cement pastes, mortars, and concretes with water-Cementitious material ratios ranging from dosage: 5% to 10% .The segregation of cement paste is caused by high super plasticizer dosages that do not cause segregation of concrete with the same water-Cementitious material ratio. Concrete containing G-FINETMas a partial replacement for cement exhibits an increased compressive strength because of the improved strength of its cement paste constituent. Changes in the paste-aggregate interface caused by silica fume appear to have little effect on the uniaxial compressive strength of concrete.PACKAGINGS G-FINE shall be packed and supplied in 25 Kg plastic bags/Customized packing is done if required in G-Fine brand. It is also available in Bulk Jumbo bags. STORAGE  G-FINE  when stored correctly has an indefinite shelf life. Like cement,G-FINE  must be protected from contamination and moisture. The product can be stored in bulk in a clean, dry storage silo.SAFETY INFORMATION / DECLARATION
           Extensive testing has shown G-FINE  to be non-toxic and environmentally friendly. No known significant health risks are associated with G-FINE but high concentrations of dust may cause irritation. It is recommended that suitable Protective clothing, gloves and eye/face protection is worn. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. The following information has been obtained from test results in an accredited laboratory. Although the information is accurate, variation in specific parameters might occur from time to time. No guarantee is therefore given or implied and GURU CORPORATION disclaims any liability from damage or consequential loss.



 

• G-GROUT MF-8 INCEPTION. G- GROUT MF-8 is highly fluid,single component, cementitious grout pre packed.
• G-GROUT MF-8 powder  It is manufactured by unique PSD technology to facilitate easy to inject and effective deep fine cracks,pores and voids. 
• It has much finer particle size than other hydraulically setting materials. 
• It is produced in state of art manufacturing plants in a controlled environment resulting in excellent filling quality.
• Purpose: G- GROUT MF-8 is suitable for injecting and grouting in rock, soil, concrete and masonry and for filling joints, cracks and holes. 
• MF-8 can be used at vertical and horizontal surfaces working. MF-8 is a ready-to-use dry-blend mortar based on cement modified with organic additives, which hardens without shrinkage when mixed with water
• Benefit: G-GROUT MF-8 can be injected with standard cement grouting equipment
• Compatible with most of the admixtures to accelerate / retard the setting time 
• Supports all portions of structures 
• Fill up the voids in concrete structure, control or prevent the structure from leakage or weak structures to strengthen 
• Non-toxic, Non-Hazards 
• Eco friendly & Cost Effective

TECHNICAL SPECIFICATION

• Properties                   G-Grout Value
• Consistency                Dry Powder
• Colour                          Grey

METHODS OF USES·    Pre-process:

• The substrate must be cleaned down to load bearing grain structure. Before grouting the substrate is to be rinsed until it is saturated excess water will be removed. 
• Mixing:
• MF-8 should be mixed with a slowly rotating mixer to avoid air pockets. First add 2/3 of the totally required water. After mixing for a short time add the balance of water. It should be mixed for approx. 6 minutes. 
• Plastic consistency for vertical and overhead surfaces: 4 litres of water per 20 kg bag Liquid consistency for injection as per requirement.
• Packaging: G-GROUT MF-8 is available in Bulk Jumbo bags with plastic inner liner. The product is also available in 25 kg plastic line bags.
• Storage: G-GROUT MF-8 when stored correctly has an indefinite shelf life. Like cement, it must be protected from contamination and moisture. The product can be stored in bulk in a clean, dry storage silo. 
• Shelf life is at least 12 month in original packaging when stored in dry conditions between 15-25°C, protected from heat, frost and direct sunlight. 
• Safety Information: Extensive testing has shown G-GROUT MF-8 to be non-toxic and environmentally benign. No known significant health risks are associated with G-GROUT MF-8 but high con-centrations of dust may cause irritation. 
• It is recommended that suitable protective clothing, gloves and eye/face protection is worn. 
• In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice.

Description

G-FINE ULTRAFINE is a new generation Supplementary Cementitious material (SCM) with a built-in high tech content. It is processed based on high glass content with high reactivity obtained through the process of controlled granulation process results in unique particle size distribution. The raw materials are composed primarily of low calcium silicate based mineral additives.

 Its latent hydraulic property and pozzolanic reactivity results in an enhanced hydration process. Addition of G-FINE improves the packing density of the paste component. In spite of its high fineness the results are in lowering water demand, admixture dosage and hence improving strength and durability parameters of concrete at all ages.

G-FINETM are observed in the concrete mix design, the initial rate of strength development was found to be increased or similar as other pozzolanic materials.

Application

•   Roads, Residential, Commercial structures
•    Producing mass concrete for raft and pile foundations
•    Low water to binder rations for high performance concrete
•    Better retention of workability and faster initial strength gain

High Strength construction work in low or high temperature weather

Benefits

 

          · Increase compressive strength ,permeability, workability of concrete

· Improves the durability of concrete  

· It can be used in waterproofing as an additive

· It can decrease the heat of hydration

·Resistance against saltwater & chemicals

· Non-Toxic, Eco friendly

            · Cost effective, economical solutionDOSAGE These goals are accomplished using cement pastes, mortars, and concretes with water-Cementitious material ratios ranging from dosage: 5% to 10% .The segregation of cement paste is caused by high super plasticizer dosages that do not cause segregation of concrete with the same water-Cementitious material ratio. Concrete containing G-FINETMas a partial replacement for cement exhibits an increased compressive strength because of the improved strength of its cement paste constituent. Changes in the paste-aggregate interface caused by silica fume appear to have little effect on the uniaxial compressive strength of concrete.PACKAGINGS G-FINE shall be packed and supplied in 25 Kg plastic bags/Customized packing is done if required in G-Fine brand. It is also available in Bulk Jumbo bags. STORAGE  G-FINE  when stored correctly has an indefinite shelf life. Like cement,G-FINE  must be protected from contamination and moisture. The product can be stored in bulk in a clean, dry storage silo.SAFETY INFORMATION / DECLARATION
           Extensive testing has shown G-FINE  to be non-toxic and environmentally friendly. No known significant health risks are associated with G-FINE but high concentrations of dust may cause irritation. It is recommended that suitable Protective clothing, gloves and eye/face protection is worn. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. The following information has been obtained from test results in an accredited laboratory. Although the information is accurate, variation in specific parameters might occur from time to time. No guarantee is therefore given or implied and GURU CORPORATION disclaims any liability from damage or consequential loss.

Description

G-FINE ULTRAFINE is a new generation Supplementary Cementitious material (SCM) with a built-in high tech content. It is processed based on high glass content with high reactivity obtained through the process of controlled granulation process results in unique particle size distribution. The raw materials are composed primarily of low calcium silicate based mineral additives.

 Its latent hydraulic property and pozzolanic reactivity results in an enhanced hydration process. Addition of G-FINE improves the packing density of the paste component. In spite of its high fineness the results are in lowering water demand, admixture dosage and hence improving strength and durability parameters of concrete at all ages.

G-FINE are observed in the concrete mix design, the initial rate of strength development was found to be increased or similar as other pozzolanic materials.

Application

§   Roads, Residential, Commercial structures

§   Producing mass concrete for raft and pile foundations

§   Low water to binder rations for high performance concrete

§   Better retention of workability and faster initial strength gain

High Strength construction work in low or high temperature weather

Benefits

 

          · Increase compressive strength ,permeability, workability of concrete

· Improves the durability of concrete  

· It can be used in waterproofing as an additive

· It can decrease the heat of hydration

·Resistance against saltwater & chemicals

· Non-Toxic, Eco friendly

            · Cost effective, economical solution DOSAGE These goals are accomplished using cement pastes, mortars, and concretes with water-Cementitious material ratios ranging from dosage: 5% to 10% .The segregation of cement paste is caused by high super plasticizer dosages that do not cause segregation of concrete with the same water-Cementitious material ratio. Concrete containing G-FINETMas a partial replacement for cement exhibits an increased compressive strength because of the improved strength of its cement paste constituent. Changes in the paste-aggregate interface caused by silica fume appear to have little effect on the uniaxial compressive strength of concrete. PACKAGINGS G-FINE shall be packed and supplied in 25 Kg plastic bags/Customized packing is done if required in G-Fine brand. It is also available in Bulk Jumbo bags. STORAGE  G-FINE  when stored correctly has an indefinite shelf life. Like cement, G-FINE  must be protected from contamination and moisture. The product can be stored in bulk in a clean, dry storage silo. SAFETY INFORMATION / DECLARATION
           Extensive testing has shown G-FINE  to be non-toxic and environmentally friendly. No known significant health risks are associated with
G-FINE but high concentrations of dust may cause irritation. It is recommended that suitable Protective clothing, gloves and eye/face protection is worn. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. The following information has been obtained from test results in an accredited laboratory. Although the information is accurate, variation in specific parameters might occur from time to time. No guarantee is therefore given or implied and GURU CORPORATION disclaims any liability from damage or consequential loss.